Use drilling when the main requirement is an economical round hole, and milling when the part needs a slot, pocket, flat, or controlled contour. A CNC shop may combine both operations in one setup, but tool access, hole accuracy, chip evacuation, wall stiffness, datums, and inspection determine the reliable route. Milling can generate some holes by interpolation; that flexibility does not make it the best choice for every standard hole.
How Drilling and Milling Remove Material
In drilling, the drill rotates and feeds axially into the workpiece. Its cutting lips create a cylindrical hole while the flutes carry chips out. Spotting, peck cycles, coolant delivery, and tool selection help maintain the hole location and clear chips, especially in deep or difficult materials.
In milling, a rotating cutter removes material as the machine moves the tool or workpiece along a programmed path. An end mill can cut laterally and axially to create pockets, slots, shoulders, and contours. The cutter’s reach, engagement, rigidity, and toolpath affect wall accuracy, chatter, finish, and cycle time.
Key Differences That Affect a CNC Part
Drilling is usually direct and efficient for round holes, particularly when a standard drill size and moderate tolerance meet the function. Hole size and location still depend on runout, material, entry geometry, workholding, and tool wear. A drilled hole that needs a close fit, improved finish, or better alignment may need reaming, boring, or another finishing step.
Milling supports more varied geometry and can adjust feature size through toolpath offsets. This is useful for slots, pockets, non-round openings, and selected larger holes made by circular interpolation. Long cutter overhang, thin walls, corner radii, and interrupted cuts can add deflection or cycle time. The route should be selected from the drawing and assembly need.
For a deeper look at milling operations, see the CNC milling process and common operations. When a feature is a through-hole, the through-hole drilling and design guide covers breakthrough, burrs, and hole inspection.
When Drilling Is the Better Starting Point
- Round clearance holes, pilot holes, and ordinary mounting-hole patterns.
- Production parts with repeated standard diameters and suitable access for a drill.
- Features where a dedicated drill cycle is faster than a milled circular toolpath.
- Parts where drill, reamer, or bore-gauge inspection matches the fit requirement.
For precision dowel, bearing, or sealing features, do not assume a drill alone will establish final size, form, position, or finish. The process may begin with drilling and continue with reaming or boring. Define the functional datum scheme and the required inspection method before production.
When Milling Is the Better Starting Point
- Slots, pockets, open cavities, steps, and flat surfaces.
- Non-round or adjustable openings, or a large hole where interpolation suits the geometry.
- Features that must share a setup and datum relationship with nearby milled surfaces.
- Low-volume parts where a flexible cutter path avoids a dedicated special tool.
Milling a hole can help when the diameter is nonstandard, the wall is thin, or the same cutter must finish related features. A helical path may improve control in some cases, but feasibility depends on tool diameter, machine rigidity, material, depth, chip evacuation, and the hole’s tolerance. A bore gauge or CMM may be needed where pin gauges do not establish the required geometry.
Combining Drilling and Milling in One Setup
Many machined parts need both operations. A bracket may use drilled mounting holes plus milled slots; a manifold may combine drilled passages with milled faces and pockets. Completing related features in one setup can reduce datum transfer error and handling, provided the tools can reach the features and chips can be cleared safely.
Sequence operations around the part’s stiffness and datum needs. Rough milling can release stress or reduce support before final holes are made, while drilling first may provide useful locating features for later workholding. The shop should review tool clearance, clamp interference, cross-hole intersections, burr access, and whether a second setup changes critical relationships.
When hole fit depends on the fastener and finish, use the metric and imperial clearance-hole chart as a starting reference, then confirm the actual screw, coating, and assembly allowance.
Tolerances, Datums, and Inspection
Call out the dimensions and geometric controls that affect assembly, not a blanket tight tolerance for every feature. A mounting-hole diameter may need a pin gauge or bore gauge; a hole pattern may need CMM true-position inspection; and a milled slot may need width, location, flatness, or profile checks. The inspection method should agree with the drawing’s datum references and feature function.
Selected stable features may require a tolerance such as +/-0.01 mm, but achievable results depend on material, size, tool reach, setup count, temperature, burr condition, and measurement uncertainty. For repeat batches, first article inspection should confirm the process and datums; in-process checks should track tool wear and dimensional drift.
Material, Chips, and Surface Finish
Aluminum often cuts efficiently but can form built-up material on a dull tool. Stainless steel can work-harden if the tool rubs or the feed is too light. Plastics need sharp tooling and heat control to limit melting or distortion. In deep holes and pockets, chip packing can damage the tool or mark the surface, so coolant, air, pecking, and toolpath strategy must match the material and geometry.
Specify surface finish only where function requires it, such as a sealing face, sliding surface, or locating shoulder. Deburring also needs a clear limit: remove sharp edges and loose material without rounding a datum, changing a slot width, or damaging the first thread.
Cost and Supplier Questions
Drilling often has a short cycle for repeated standard holes, while milling can reduce special tooling or combine multiple shapes in one route. Total cost also includes setup, tool changes, chip clearing, deburring, inspection, fixture requirements, and any finishing operation. A nominally faster cut may not be economical if it increases scrap or requires difficult inspection.
- Which features will be drilled, interpolated, reamed, or bored, and why?
- How will hole position, fit, slot width, and datum relationships be measured?
- Can the part remain in one setup, and how will thin walls be supported?
- How will chips and burrs be controlled at blind holes, cross-holes, and pockets?
- Will the quoted inspection include FAI, CMM results, gauge checks, and batch records?
Provide the current drawing and model, material and condition, quantity, critical features, finish, and inspection requirements in the RFQ. This lets the supplier compare a practical route instead of quoting only a machine operation name.
Frequently Asked Questions
1. What is the main difference between drilling and milling?
Drilling feeds a rotating drill along its axis to create a round hole. Milling moves a rotating cutter along a programmed path to create surfaces, slots, pockets, contours, and some holes.
2. Is drilling faster than milling?
Drilling is often faster for standard round holes because one drill cycle can make the feature directly. Milling may be more efficient for a non-round feature, a large interpolated hole, or several shapes that share a setup.
3. Can a milling machine make holes?
Yes. A mill can drill holes with a drill tool and can generate selected holes with circular or helical interpolation. The right method depends on diameter, depth, tolerance, finish, material, and available tooling.
4. Can drilling make a slot or pocket?
Drilling makes round holes rather than a controlled slot or pocket. Overlapping drilled holes may remove bulk material, but milling is normally needed to establish the feature’s final walls, width, and shape.
5. Which process gives a more accurate hole?
Neither process guarantees accuracy by itself. A drilled hole may need reaming or boring for final size, alignment, or finish; interpolated milling may help with selected sizes and geometries. Drawing requirements and inspection method decide.
6. Should a precision hole be drilled or milled?
It may be drilled first, then reamed or bored. Milling interpolation can be suitable for some hole sizes or thin-wall conditions. The supplier should review tolerance, depth, material, datum access, and measurement needs.
7. Is CNC milling more expensive than drilling?
It depends on cycle time, setup, tooling, quantity, geometry, inspection, and secondary operations. Drilling is commonly economical for many repeated standard holes, while milling can avoid special tooling and create multiple features.
8. What causes a drilled hole to wander?
Runout, a poor starting surface, long tool overhang, uneven material, weak workholding, chip packing, and unsuitable feeds can push a drill off its intended axis. Spotting, rigid support, and the correct cycle reduce risk.
9. How are drilled holes and milled slots inspected?
Pin gauges or bore gauges can check hole size; a CMM can verify position and datum relationships. Slots may need width, location, profile, flatness, or surface-finish checks using methods suited to their geometry.
10. Can drilling and milling be combined on one CNC part?
Yes. A CNC part can include drilled holes and milled faces, slots, and pockets. One setup can improve feature relationships when tool access, clamping, chip removal, and inspection remain practical.
Final Thoughts
Drilling and milling serve different feature needs, and a reliable CNC route may use both. Start with the geometry and functional datums, then account for tolerance, material, workholding, burr control, cycle time, and inspection. That process-based review helps the factory meet assembly requirements without adding unnecessary operations or precision.
Related DAXIN Services
DAXIN supports CNC drilling, milling, reaming, boring, tapping, deburring, FAI, CMM inspection, and prototype or repeat production for precision components.
Request a CNC Machining Review
Send the drawing, model, material, quantity, critical dimensions, finish, and inspection requirements through the DAXIN contact page. We can review the operation sequence, tool access, datum strategy, and production risks before quoting.